Precision Gage Solutions: September 2009

Wednesday, September 16, 2009

The Fastener Black Book is Now Available at Thread Check

THE FASTENER BLACK BOOK IS NOW AVAILABLE!. Click Here To See More Info.

The Fastener Black Book is a comprehensive pocket book reference guide for engineers, machinist, and gauging professionals. Look at everything it includes!
- Thread Forms - Inch / Metric Fasteners - ISO & DIN Specifications - Fastener Plating & Finishes - Pre-loads & Tightening Torques	- Heads, Points, Materials,Coatings - Thread Terminology & Classifications - Standard Grades, Tolerances & Markings, and much more!
$27.00

Check Out Our New Look and Expanded Product Range!

Thread Check Inc. Precision Gage Solutions | 390 Oser Ave., Hauppauge, New York 11788 USA
info@threadcheck.com | www.threadcheck.com | tel: 800.767.7633 | fax: 800.767.2034

Thursday, September 3, 2009

Thread Check Has a New Website and New Products!

CHECK OUT OUR NEW WEBSITE AND EXPANDED PRODUCT RANGE! Click Here To See Our Exciting New Website.

CHECK OUT OUR NEW LOOK
AND EXPANDED PRODUCT RANGE!

Thread Check, Inc. is a full service gage company offering a
complete line of precision thread gages, plain cylindrical
gages, custom gages, patented 3 wire thread measuring
systems, API pipe gages, tri roll thread comparators,
powerful thread engineering software, gear measuring
wires & instruments, cutting tools, ISO 17025 Registered
calibration services, and free technical support.

Test our Commitment to Quality, Service, and
Competitive Prices!

TOP PRODUCTS

Thread Check Inc. Precision Gage Solutions | 390 Oser Ave., Hauppauge, New York 11788 USA
info@threadcheck.com | www.threadcheck.com | tel: 800.767.7633 | fax: 800.767.2034

Proper Care And Usage Of Gages

Part dimensions to be gaged should be cleaned and burr free to prevent gaging interference. Grit and part chips which become lodged in thread gages will create scratches and wear on the flanks of threads and on the outside and inside diameters of cylindrical plain gages. Various materials such as aluminum and castings are extremely abrasive and will tend to wear out gages more quickly than other types of materials. Finer pitch and smaller diameter thread gages tend to wear quicker than larger and coarser pitch gages and have less gage tolerance as well. Regarding thread gages, it only takes a small amount of wear to have a significant effect on the pitch diameter. The wear on each flank angle is multiplied by almost 4 times to determine the total impact of wear on the pitch diameter. 50 microinches or 1 micron of wear per thread flank will impact the measured size by .0002” which can be the total tolerance of many thread gages.

Selecting higher precision gagemaker tolerances for cylindrical plug and ring gages will consume less product tolerance and will allow the acceptance of slightly more product but with less gage wear life and greater expense. Thread Check’s engineering staff can make recommendations in selecting the correct gagemaker tolerances for a given application. The normal rule of practice requires that 10% of part tolerance be divided between the Go and the No Go gages. Applying this practice results in gage tolerance always being included in the part tolerance by up to 10%.This could result in the possibility that 10% of good parts may fail inspection but that no bad product would ever pass. Assuming that higher precision gagemaker tolerances are better, is not valid, and may create quality issues as these gages tend to wear quicker with the potential of becoming undersized and passing bad parts.

Gages should be turned or pushed slowly and gently into or onto the dimension being checked. Forcing gages will result in faulty gaging and the possibility of damaging both the part and gage. Spinning thread ring gages or thread plug gages onto or into parts will create greater friction and increased wear thus reducing the life of the gage.

Using hard chrome plated thread gages can extend the wear life by more than 100% over standard tool steel gages which can provide dramatic savings on replacement costs. Thread Check supplies all standard size thread plug gages in inches and metric up to 1 ½ or 39mm in diameter in hard chrome at no additional cost. Other options for coatings and alternate material for thread gages and cylindrical gages include tin coat, carbide, alternate steels and even ceramic. There are pros and cons to utilizing various coatings and materials in gage applications which should be discussed with your gage maker. For example, gages made of carbide and ceramic are extremely durable and have excellent wear properties, but can be extremely brittle and break and chip if not handled carefully. Read More about Proper Care And Usage Of Gages

Precision Gage Solutions

Wednesday, September 16, 2009

The Fastener Black Book is Now Available at Thread Check

Thursday, September 3, 2009

Thread Check Has a New Website and New Products!

Search Precision Gage Solutions

Thread Check Catalog Request

ThreadTech™ v2.24 Software

Precision Gage Solutions Links

Precision Gage Solutions Posts

Precision Gage Solutions Archive

Proper Care And Usage Of Gages

Followers