Precision Gage Solutions: Thread Check Gages Last Longer!

Tuesday, October 20, 2009

Thread Check Gages Last Longer!

	THREAD CHECK GAGES LAST LONGER! Thread Check, Inc. offers Chrome Plating on all standard stocked thread plug gages at no additional charge. Chrome plating can extend the wear life of a gage by more than 100% which provides dramatic savings on replacement costs. Thread Check’s chrome plated standard plug gages are available in both taperlock and reversible style. All Thread Check, Inc. gages are manufactured to the high end of the tolerance to ensure longer gage life. All gages are traceable to the National Institute of Standards and Technology - NIST. Thread Check, Inc. also manufactures many types of special gages including pre-plates, multiple starts, special leads, acme thread gages, API thread gages, buttress thread gages, spline gages, trapezoidal gages, flex hole location gages, British thread gages, STI Helical Coil gages, square thread gages, extra length thread gages, plain cylindrical gages, and custom gages to print.


	Receive a FREE giant 2' x 3' Thread Check pitch diameter and gage tolerance wall chart with your next order. The wall chart is a great reference aid for your production facility or calibration department. CONTACT US NOW FOR ALL YOUR GAGING REQUIREMENTS. CALL 800 767 7633 or 631 231 1515

Thread Check Inc. Precision Gage Solutions | 390 Oser Ave., Hauppauge, New York 11788 USA
info@threadcheck.com | www.threadcheck.com | tel: 800.767.7633 | fax: 800.767.2034

No comments:

Post a Comment

Proper Care And Usage Of Gages

Part dimensions to be gaged should be cleaned and burr free to prevent gaging interference. Grit and part chips which become lodged in thread gages will create scratches and wear on the flanks of threads and on the outside and inside diameters of cylindrical plain gages. Various materials such as aluminum and castings are extremely abrasive and will tend to wear out gages more quickly than other types of materials. Finer pitch and smaller diameter thread gages tend to wear quicker than larger and coarser pitch gages and have less gage tolerance as well. Regarding thread gages, it only takes a small amount of wear to have a significant effect on the pitch diameter. The wear on each flank angle is multiplied by almost 4 times to determine the total impact of wear on the pitch diameter. 50 microinches or 1 micron of wear per thread flank will impact the measured size by .0002” which can be the total tolerance of many thread gages.

Selecting higher precision gagemaker tolerances for cylindrical plug and ring gages will consume less product tolerance and will allow the acceptance of slightly more product but with less gage wear life and greater expense. Thread Check’s engineering staff can make recommendations in selecting the correct gagemaker tolerances for a given application. The normal rule of practice requires that 10% of part tolerance be divided between the Go and the No Go gages. Applying this practice results in gage tolerance always being included in the part tolerance by up to 10%.This could result in the possibility that 10% of good parts may fail inspection but that no bad product would ever pass. Assuming that higher precision gagemaker tolerances are better, is not valid, and may create quality issues as these gages tend to wear quicker with the potential of becoming undersized and passing bad parts.

Gages should be turned or pushed slowly and gently into or onto the dimension being checked. Forcing gages will result in faulty gaging and the possibility of damaging both the part and gage. Spinning thread ring gages or thread plug gages onto or into parts will create greater friction and increased wear thus reducing the life of the gage.

Using hard chrome plated thread gages can extend the wear life by more than 100% over standard tool steel gages which can provide dramatic savings on replacement costs. Thread Check supplies all standard size thread plug gages in inches and metric up to 1 ½ or 39mm in diameter in hard chrome at no additional cost. Other options for coatings and alternate material for thread gages and cylindrical gages include tin coat, carbide, alternate steels and even ceramic. There are pros and cons to utilizing various coatings and materials in gage applications which should be discussed with your gage maker. For example, gages made of carbide and ceramic are extremely durable and have excellent wear properties, but can be extremely brittle and break and chip if not handled carefully. Read More about Proper Care And Usage Of Gages

Precision Gage Solutions

Tuesday, October 20, 2009

Thread Check Gages Last Longer!

No comments:

Post a Comment

Search Precision Gage Solutions

Thread Check Catalog Request

ThreadTech™ v2.24 Software

Precision Gage Solutions Links

Precision Gage Solutions Posts

Precision Gage Solutions Archive

Proper Care And Usage Of Gages

Followers